Köşe Radyüslü ve Düz Uçlu Parmak Freze: Hangisini Seçmelisiniz?
Two end mills can share the same diameter and flute count yet leave different bottom corners. In a corner radius end mill vs square end mill comparison, the part drawing sets the first limit.
Hızlı Cevap
Square end mill
Use for a nearly square floor-to-wall corner. Confirm the allowed radius or edge break.
Corner radius end mill
Use when the selected R fits the drawing and added corner support benefits the cut.
If both profiles fit
Compare the complete tool and trial results. Keep an approved square model if it already meets the job.
İçindekiler6 sections
01 Corner Radius End Mill vs Square End Mill: Key Differences
A corner radius tool rounds the junction between the end and peripheral cutting edges. A square tool has a nominally square junction. The distinction matters where the cutter finishes the floor-to-wall transition.
| Compare | Square end mill | Corner radius end mill |
|---|---|---|
| Cutting corner | Nominal 90° corner. | Specified corner radius, R. |
| Bottom transition | Near-square transition, within the allowed corner radius or edge break. | Rounded fillet in a simple shoulder-finishing pass. |
| Flat floor | Can machine a flat floor. | Also retains a flat-bottom region. |
| Corner support | Sharp corners can be vulnerable under concentrated loading. | A radius reinforces the corner and can reduce corner chipping. |
On mobile, swipe the table to compare all columns.
Which “inside corner” does the drawing mean?
SECTION VIEW
Floor-to-wall fillet
Check the tool’s corner R. In a simple shoulder-finishing pass, it forms the bottom fillet. Confirm the allowed radius and any mating-part clearance.
TOP VIEW
Inside corner between two walls
Kontrol et cutter diameter and toolpath. In ordinary peripheral milling, neither profile makes a zero-radius XY inside corner. A smaller cutter or another finishing process may be needed.
For square tools: a small edge hone or protective chamfer may be present. State the permitted residual radius and any allowed chamfer separately; they are different geometries.
02 When Should You Choose Each Profile?
Start with the required corner. Once the profile fits, use our solid carbide end mill selection guide to compare flute design, carbide grade, coating and cutting data for the actual material and operation.
Square end mill
- The finished feature calls for a nearly square floor-to-wall corner.
- The tool’s corner preparation stays within the drawing’s allowed radius or edge break.
Steel-series example: HRC55 four-flute square end mill →
Corner radius end mill
- The required or permitted floor-to-wall fillet can be produced with the selected R.
- The operation calls for more support at the cutting corner.
Steel-series example: HRC55 four-flute TiSiN corner radius end mill →
These product examples are steel-milling series. For stainless steel or another material, confirm a suitable model and coating separately; a matching corner profile alone does not establish suitability.
When Both Profiles Fit the Drawing
When both profiles can meet the part requirements, compare the full geometry, material suitability and machining results. Keep an approved square model if it already gives the required dimensions, finish and tool life.
For a new application, a radius tool can be evaluated from the start. Both profiles can suit side milling, slotting or pocketing when chip space, reach, entry capability and the complete cutting design fit the job.
For a four-flute order in steel or stainless steel, work through the four-flute end mill selection checks to confirm the material range, dimensions and cutting geometry.
Have a drawing section to check?Ask HY Cutting Tools about the profile and size.
03 How to Choose the Corner Radius
Read the radius callout before choosing a tool. A maximum corner radius and a specified finished radius with upper and lower limits lead to different checks.
- Maximum radius: the finished fillet must stay within that limit. A nominal tool R at the limit still needs its manufacturing tolerance and the machining result checked.
- Specified radius and tolerance: both limits matter. A smaller tool R may leave an undersized fillet in a simple shoulder-finishing pass.
Compare available diameter/R combinations and confirm the tool’s R tolerance. For a critical fillet, agree the cutter inspection method and check the finished part during the trial.
EXAMPLE INQUIRY · DIMENSIONS IN mm
D10 R0.5 → D10 R1?
In a simple shoulder finish, R1 leaves a larger floor-to-wall fillet. If the drawing permits R0.5 maximum, R1 exceeds that limit. The matching diameter does not make it a suitable substitute.
If the requested diameter/R or reach is unavailable, check a regular size or series variant first. For a modified or custom tool, agree the drawing revision, quantity per design and first-order costs.
For 3D finishing toolpaths
For 3D finishing, review cutter geometry and the CAM strategy together. The simple shoulder example does not cover every generated surface; check the finished feature before approving a different R.
04 What to Confirm Before Ordering or Replacing a Tool
- Confirm the supplied specification: compare cutting diameter (D), corner profile/R and tolerances, flute count, cutting length (L1), shank diameter (d), overall length (L), usable reach, geometry and coating with the order or approved drawing. State the units and quantity for each size; matching diameter and overall length do not confirm an equivalent tool.
- For a replacement: record what changes and why. If the current tool chips, photograph every flute and check mounting, runout and corner engagement before choosing a different profile.
- For a new or changed model: agree the part checks and trial stopping criteria. Measure the fillet, dimensions and finish, then compare wear after a defined cutting length or number of parts.
Use cutting conditions suitable for each model and record any setting changes. Keep the workpiece, operation and comparison workload consistent. Use our cutting tool trial order guide to agree acceptance checks and feedback before a larger order.
Retain the accepted specification, trial conditions and results for repeat orders. For vibration problems, see our chatter troubleshooting guide.
05 Buying and Replacement FAQs
Can I replace a square end mill with a corner radius version of the same diameter?
Only if the proposed corner meets the part drawing and the full tool suits the cut. Have the customer approve a changed R or profile before ordering a replacement.
Can you match the end mill my customer is already using?
We can check for a suitable alternative. Send HY Cutting Tools the brand, full tool code and label photo, plus the workpiece material, operation and quantity per size.
A photo can start the comparison. Use a drawing or reference tool to confirm dimensions; the final R and tolerance need agreement before approval.
What should I ask for if the corner radius is critical?
Ask for the nominal R, manufacturing tolerance and inspection method on the quotation or approved drawing. Agree which measured values will be supplied and whether inspection applies to the finished coated tool.
Tool inspection checks the cutter. Measure the finished fillet during the trial as a separate acceptance check.
Does an unusual R mean I need a custom tool?
Not necessarily. Check for a suitable standard diameter/R and reach combination first. If none fits, HY Cutting Tools can review a drawing or physical sample.
Confirm the proposed geometry, tolerances, quantity and lead time before ordering.
Can I try a few pieces or combine different sizes?
Yes. HY Cutting Tools accepts trial orders, and different sizes can generally be combined. Send the quantity for each diameter/R so the applicable MOQ can be checked.
Samples are normally charged, and freight is paid by the buyer.
How do I make sure the repeat order matches the approved sample?
Keep the approved model or drawing revision, R/tolerance, geometry and coating with the trial conditions, results and acceptance limits. Reference that record on the repeat purchase order.
Confirm any proposed changes with your customer before shipment. Agree which critical dimensions will be checked on repeat batches.
For payment, shipping and general order terms, see our buyer FAQs.
Technical references:Harvey Performance: end mill profiles; Sandvik Coromant: inside-corner engagement.
Check Your Tool Specification
Send HY Cutting Tools the drawing section, workpiece material and required tool sizes. For a replacement, include the current model and clear photos of the cutting corner.
Details to include with your enquiry
- Part: marked drawing section, material grade/hardness and operation.
- Tool: diameter, R, tolerances, cutting length, shank, OAL and required reach.
- Sipariş: quantity per diameter/R; current model and edge photos if replacing a tool.






